Manufacturer
8 TON
Model
LONG RAM HYDRAULIC JACK
Condition
Used
Stock Number
160
Description
Manufacturer: Not Provided Model Number: Not Provided Serial Number: Not Provided Condition: Not Specified Operating Condition: NOT TESTED – OPERATING CONDITION UNKNOWN Equipment Type: Long Ram Hydraulic Jack / Lifting Cylinder Rated Lifting Capacity: 8 Tons (16,000 lbs – U.S. Short Tons) Power Source: Hydraulic Primary Application: Engine Hoists, Shop Cranes & Compatible Lifting Equipment Lot Location: 1216 Olean Trail, New Bethlehem, PA 16242 LONG RAM HYDRAULIC JACK SPECIFICATIONS Specification Details Equipment Type Long Ram Hydraulic Jack Manufacturer Not Provided Model Number Not Provided Advertised Lifting Capacity 8 Tons Equivalent Capacity 16,000 lbs – U.S. Short Tons Operating System Hydraulic Jack Configuration Long Ram / Extended Stroke Hydraulic Cylinder Steel Construction – Typical Ram Material Steel Lifting Stroke Model Dependent Typical Published Stroke Approximately 18–20 Inches Minimum Height Model Dependent Maximum Extended Height Model Dependent Pump Type Manual or Air/Hydraulic – Verify Actual Unit Pump Handle Inclusion Not Confirmed Air Connection Only on Air/Hydraulic Models Mounting Configuration Model Dependent Clevis Mounting Common on Engine Hoist Applications Mounting Pin Diameter Model Dependent Hydraulic Fluid Manufacturer-Specified Hydraulic Jack Oil Pressure Release Controlled Hydraulic Release – Typical Overload Protection Model Dependent Primary Applications Engine Hoists, Shop Cranes & Compatible Lifting Systems Operating Condition Not Tested Load Testing Not Performed Specification Note: Published 8-ton long ram hydraulic jacks commonly feature lifting strokes of approximately 18–20 inches, but dimensions and configurations vary. Some models operate with a manual hydraulic pump, while others incorporate compressed-air assistance. The actual jack must be inspected to determine its configuration, specifications, and operating requirements. LONG RAM HYDRAULIC JACK FEATURES Heavy-duty 8-ton long ram hydraulic jack. Advertised lifting capacity of 16,000 pounds. Long-stroke hydraulic cylinder design. Designed for use with compatible lifting equipment. Suitable for engine hoist and shop crane applications. Hydraulic lifting mechanism. Extended ram design for increased lifting travel. Steel cylinder construction commonly used in this equipment category. Designed for controlled raising and lowering of loads. Can be incorporated into compatible shop lifting systems. Commonly used in automotive and mechanical repair facilities. Suitable for agricultural equipment maintenance applications. Designed for use with appropriately rated mounting hardware. Hydraulic system requires proper fluid levels and maintenance. Actual lifting stroke depends on the manufacturer and model. Actual mounting configuration must be verified. Operating condition has not been confirmed. COMMON APPLICATIONS When properly installed and used within its rated capacity, this type of jack may be suitable for: Engine hoist lifting systems. Automotive engine removal and installation. Shop crane hydraulic lifting. Mechanical repair shop operations. Agricultural equipment maintenance. Farm equipment repair. Industrial maintenance operations. Equipment service facilities. Replacing compatible hydraulic lifting cylinders. Workshop lifting equipment. Automotive restoration projects. Machinery maintenance. General mechanical lifting applications. Commercial garage operations. Compatible portable shop crane systems. Application Note: This jack is intended for use with compatible lifting equipment. Its advertised 8-ton capacity does not establish the rated lifting capacity of an assembled engine hoist or shop crane. EQUIPMENT CONDITION Overall Condition: Not Specified Operating Condition: NOT TESTED – UNKNOWN Hydraulic Cylinder: Not Operationally Tested Hydraulic Pump: Not Operationally Tested Ram Extension: Not Tested Ram Retraction: Not Tested Hydraulic Seals: Condition Not Verified Hydraulic Fluid Level: Not Verified Pressure Retention: Not Tested Hydraulic Leakage: Not Tested Release Valve: Not Operationally Tested Pump Handle: Inclusion Not Confirmed Mounting Points: Not Independently Inspected Mounting Pins: Inclusion Not Confirmed Structural Condition: Not Load Tested Rated Capacity: Not Independently Verified Equipment Compatibility: Buyer Responsible for Verification Service Requirements: Inspection, Testing & Possible Servicing Recommended Before Use ADDITIONAL INFORMATION 8-ton long ram hydraulic jack. Advertised lifting capacity of 16,000 pounds. Designed for compatible engine hoist and shop crane applications. Long-stroke hydraulic cylinder configuration. Suitable for various automotive and mechanical lifting applications. Commonly utilized in equipment repair and maintenance facilities. Hydraulic lifting system. Actual manufacturer and model number have not been provided. Actual minimum and maximum lifting heights must be verified. Actual ram stroke must be verified. Pump configuration must be verified. Manual and air-assisted hydraulic versions are available in this equipment category. Mounting pin dimensions must be verified before installation. Mounting configuration must be compatible with the intended lifting equipment. Pump handle and mounting hardware are not guaranteed unless shown in the lot photographs. Hydraulic fluid level and condition have not been verified. Jack has not been independently tested under load. Hydraulic seals and pressure retention have not been tested. Operating condition is unknown. Buyer is responsible for verifying lifting capacity, compatibility, completeness, and overall condition. Additional hydraulic fluid, repairs, or servicing may be required before operation. Buyer should inspect the jack prior to bidding. IMPORTANT AUCTION NOTICE OPERATING CONDITION UNKNOWN – NOT TESTED This 8 Ton Long Ram Hydraulic Jack is being offered with its operating condition unknown unless otherwise specifically stated. The jack has not been independently tested for hydraulic operation, ram extension, ram retraction, pressure retention, lifting capacity, or overall functionality. IMPORTANT CAPACITY NOTICE: This jack is advertised with an 8-ton lifting capacity, equivalent to 16,000 pounds using U.S. short tons. Buyers must verify the manufacturer's actual rated capacity and ensure the jack is used only within its approved operating limits. IMPORTANT MANUFACTURER NOTICE: The manufacturer and model number have not been provided. Buyers should inspect the actual unit for identification markings, specifications, and operating instructions. IMPORTANT DIMENSION NOTICE: Long ram jacks vary in minimum height, maximum height, lifting stroke, and mounting dimensions. Buyers must verify all measurements before purchasing this jack for an existing engine hoist, shop crane, or other lifting system. IMPORTANT HYDRAULIC NOTICE: The hydraulic system has not been independently tested. Buyers should inspect the pump, cylinder, hydraulic seals, fluid level, release valve, and associated components before operation. IMPORTANT MOUNTING NOTICE: Proper installation requires compatible mounting points, correctly sized pins, appropriate retaining hardware, and suitable structural support. Buyers must verify compatibility with their intended equipment before use. IMPORTANT ENGINE HOIST NOTICE: The lifting capacity of an assembled engine hoist or shop crane is determined by the manufacturer's rating for the complete lifting system, including the boom position, frame, mounting hardware, and hydraulic jack. Installing an 8-ton jack does not increase the rated capacity of a lower-rated crane. IMPORTANT LOAD TESTING NOTICE: This jack has not been independently load tested. Buyers should verify proper hydraulic operation and safe lifting performance before placing it into service. IMPORTANT SERVICE NOTICE: Before operation, the buyer should inspect the hydraulic cylinder, ram, seals, pump, release valve, mounting points, and all associated components. Any necessary repairs, adjustments, or servicing are the responsibility of the buyer. IMPORTANT SAFETY NOTICE: Hydraulic lifting equipment can cause serious injury or property damage if improperly installed or operated. Never exceed rated lifting capacities, work beneath a load supported only by a hydraulic jack, or use lifting equipment with damaged structural or hydraulic components. Loads must be supported by appropriately rated mechanical supports when required. Buyers are encouraged to inspect the jack prior to bidding to verify condition, completeness, specifications, mounting compatibility, and operating suitability. Item sells AS IS, WHERE IS, in accordance with the auction's published terms and conditions.